MOTEC INJECTOR DESCARGAR DRIVER

MOTEC INJECTOR DRIVER DETAILS:

Type: Driver
File Name: motec_injector_30669.zip
File Size: 8.3 MB
Rating:
4.37
11 (4.37)
Downloads: 9
Supported systems: Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit
Price: Free* (*Free Registration Required)

Download Now
MOTEC INJECTOR DRIVER



motec injector Best Match currently selected. Gallery View. Injector max voltage V. Servo Control Allows the use of a 3D table to control a fast response, high torque DC or stepper motor.

MOTEC M1 DATA

Motec injector, Multispark Enables configuring ignition to fire multiple times and injectors to open twice per motec injector. Related Documentation:. Close Step 1 of 2: Register Please enter your details below to register for an account. Upgradable with optional functionality to make additional features available when you want them, activated through a simple password system.

For the M engine management system the following upgrades are available:. Haas Automation, Inc.

MOTEC INJECTOR DRIVERS PC

Racing Beat. Salasko Racing. Get Directions. Page Transparency See More. Facebook is showing information to help you better understand the purpose of a Page. The Telemetry Monitor software shows the ECU data in various graphical forms including dial gauges, bar graphs and chart recorders. Mass Air flow MAF sensors are also used particularly where regulations state that the sensors cannot be changed from the factory fitted sensors. A Throttle Position sensor is optional and will be used for acceleration enrichment if fitted. The MAP sensor may be used to compensate for barometric pressure changes by venting it to atmospheric pressure.

This is required so that the fuel is varied as the idle speed control valve opens and closes. The sensor will produce a voltage proportional to the angle of the motec injector plate. Motec injector sensors generally have a dead band at either end and must be pre- loaded to avoid the dead band.

MOTEC INJECTOR WINDOWS 7 DRIVERS DOWNLOAD (2019)

These parameters must be reset any time the sensor is moved or replaced. It is very important to set these parameters with the butterfly in exactly the same place motec injector time.

Motec Car & Truck Fuel Inject. Controls & Parts eBay

The resistance element inside the sensor may wear due to vibration in high performance engines motec injector can cause erratic readings. It is best to replace the throttle position sensor periodically.

Avoid high pressure washing as this may penetrate the seals and damage the sensor. For wiring details refer to the appropriate MoTeC drawing. MAP sensors normally produce a voltage between 0 and 5V, depending on the pressure. The pressure sensor may be used to measure the inlet manifold pressure or to measure the barometric pressure depending on the Load Sensing arrangement detailed earlier. Motec injector Installation 21 Avoid severe vibration of the sensor as this can cause fluctuations in the reading.

MoTeC M ECU - Race Spec

motec injector Do not mount rigidly to the engine. Normally the pressure sensor is mounted to the vehicle body. For turbo charged engines a kPa absolute sensor will measure motec injector to kPa 29 psi of boost above Atmospheric. If higher boost will be achieved a sensor with a higher pressure range will be needed.

The sensor should be connected to the inlet manifold plenum via a short hose less than 1m. The sensor should be mounted motec injector the level of the plenum with the port motec injector down to avoid moisture accumulating on the sensor element. The hose should run downwards all the way to the plenum.for YP Injectors.

  • Injector Timing on the MoTeC M1 High Performance Academy
  • Injector drivers
  • MoTeC Calibrations DeatschWerks, LLC
  • Motec M1 Series ECUs (Direct Injection)
  • MoTeC M150 ECU
  • Privacy Policy
  • MoTeC High/Low Injection Option - M84

Part No: # Denso YP Injector Connector Male. Part No: # Injector Connector Kit to Fit Uscar.

Part No. If you are running one of the Motec injector packages later than July 15, then there is a drop down list of injector Calibrations under Fuel Injector Primary.

Other Drivers